dynamic coordination is an iterative process where both interdependent activities provide input to each other.

Answer:

1.933 KN-M

Explanation:

Determine the largest permissible bending moment when the composite bar is bent  horizontally

Given data :

modulus of elasticity of steel = 200 GPa

modulus of elasticity of aluminum = 75 GPa

Allowable stress for steel = 220 MPa

Allowable stress for Aluminum = 100 MPa

a = 10 mm

First step

determine moment of resistance when steel reaches its max permissible stress

next : determine moment of resistance when Aluminum reaches its max permissible stress

Finally Largest permissible bending moment of the composite Bar = 1.933 KN-M

attached below is a detailed solution

Answer:

steep grading

Explanation:

the farthest

Detailed Design Baseline is typically established at the critical design review.

The critical design review is a significant milestone in the engineering and development process of a project.

It is conducted to assess the maturity and completeness of the detailed design of a system or product. During the CDR, the design is evaluated against the requirements, specifications, and technical constraints.

At this stage, the Detailed Design Baseline is established, which represents the agreed-upon design specifications, including architectural diagrams, engineering drawings, component selection, interfaces, and other technical details.

This baseline serves as the reference point for the subsequent stages of manufacturing, fabrication, testing, and implementation.

The establishment of the Detailed Design Baseline at the critical design review ensures that the design is well-defined and provides a foundation for further development, production, and quality assurance activities.

Any changes to the design after this point will require a formal change control process to ensure proper evaluation and impact assessment.

Learn more about Detailed Design Baseline

brainly.com/question/31765734

#SPJ11

This question is incomplete, the complete question is;

Determine the design moment strength (ϕMn) for a W21x73 steel beam with a simple span of 18 ft when lateral bracing for the compression flange is provided at the ends only (i.e., Lb = 18 ft). Report the result in kip-ft.

Use Fy=50 ksi and assume Cb=1.0 (if needed).

Answer: the design moment strength for the W21x73 steel beam is 566.25 f-ft

Explanation:

Given that;

section  W 21 x 73 steel beam;

now from the steel table table for this section;

Zx = Sx = 151 in³

also given that; fy = 50 ksi and Cb = 1.0

QMn = 0.9 × Fy × Zx

so we substitute

QMn = 0.9 × 50 × 151

QMn = 6795 k-inch

we know that;

12inch equals 1 foot

so

QMn = 6795 k-inch / 12

QMn = 566.25 f-ft

Therefore the design moment strength for the W21x73 steel beam is 566.25 f-ft

Answer:

Talcum powder!

Explanation:

How to find the source of an oil leak:

This method simply involves using Talcum Powder as a visual aid to help pinpoint the location of an oil leak,

so you use Talcum powder for small oil leak :]

Have a wonderful day!

Answer:

i hope this helps.

Explanation:

they are used for breaking concrete, can be positioned to break vertical and overhead surfaces, allows precisely chip away only specific areas.

Answer:

\❤)engineering design process(❤/

Explanation:

(♨️)BRAINLEIST PLEASE(♨️)

The head h that will produce h will be 23.92 meters.

The head, pressure, or energy (they all refer to the same thing) expended by water moving in a pipe or channel due to turbulence brought on by the water's speed and the roughness of the pipe, channel walls, or fittings. Friction losses cause water moving through a pipe to lose head.

The normal pipe head losses in small high-head, low-flow hydro systems range from 10% to 20%. Pipe head losses are typically only a few percent in low-head systems.

To know more about head loss visit:--

https://brainly.com/question/13002029

#SPJ4

Answer:

10.5

Explanation:

Measuring a Brake Drum, the Brake Micrometer is set to a Base Drum Diameter of 10 Inches plus four notches, and the dial reads 22.  Diameter of the drum is 10.5.

Any straight line segment that cuts through the center of a circle and has ends that are on the circle is considered a circle's diameter in geometry. It is also known as the circle's longest chord.

The diameter of a sphere can be defined using either of the two methods. In more recent usage, the diameter can also refer to a diameter's length, or displaystyle d.

As opposed to a diameter, which refers to the line segment itself, one uses the term "diameter" in this context since all diameters of a circle or sphere have the same length, which is equal to twice the radius "displaystyle r.

Therefore, Measuring a Brake Drum, the Brake Micrometer is set to a Base Drum Diameter of 10 Inches plus four notches, and the dial reads 22.  Diameter of the drum is 10.5.

To learn more about diameter, refer to the link:

https://brainly.com/question/5501950

#SPJ5

To create a router table for Router B, we will identify the destination network IP addresses and the IP addresses used for the next hop. Since we do not have the exact network diagram, we will provide a general example.

Assuming all network addresses use a /8 mask and the cost (hop value) for all connections is 1, and Router R is the default next hop, the router table for Router B might look like this: 1. Destination Network: 10.0.0.0/8, Next Hop IP Address: 10.0.0.2 (Router R) 2. Destination Network: 20.0.0.0/8, Next Hop IP Address: 20.0.0.3 (Router A) 3. Destination Network: 30.0.0.0/8, Next Hop IP Address: 30.0.0.4 (Router C) 4. Destination Network: 40.0.0.0/8, Next Hop IP Address: 40.0.0.5 (Router D) 5. Destination Network: 50.0.0.0/8, Next Hop IP Address: 50.0.0.6 (Router E)

Please note that the destination network IP addresses and the next hop IP addresses are just examples and should be replaced with the specific information from your network diagram.

To know more about Router visit:-

https://brainly.com/question/18875517

#SPJ11

Answer:

Stop Sign

Explanation:

It's red and shaped like an octogon

Given an int variable strawsoncamel, a statement that uses the increment operator to increase the value of that variable by 1 is; strawsOnCamel++;

When talking about Increment of an int variable in Java, we know that;

There are two ways to use the increment operator; prefix and postfix increment. The prefix increment looks like ++variablename; while the postfix increment looks like variablename++; . Both of these operations add one to the value in the variable. The difference between the two is the order of how it works.

Now, write a statement that uses the increment operator to increase the value of that variable by 1. Thus, we will make use of the postfix increment to get;

strawsOnCamel++;

Read more about Java Script Increment at; https://brainly.com/question/23335640

#SPJ1

1.) A semiconductor is a device whose conductivity lies between the conductivity of the conductors and the insulators.

2.) A Zener diode is a semiconductor device made of silicon that allows current to flow in both directions.

A semiconductor is a device whose conductivity lies between the conductivity of the conductors and the insulators.

Due to the inclusion of an impurity or temperature effects, a solid substance with conductivity between that of an insulator and that of most metals. Semiconductor devices, particularly silicon devices, are key components of most electronic circuits.

Zener diode:-

A Zener diode is a semiconductor device made of silicon that allows current to flow in both directions.

To know more about semiconductors follow

https://brainly.com/question/13800609

#SPJ4

To find ix and iy for the shaded area shown using integration and the composite body approach, we can follow the steps outlined in textbook problems 9.93 and 9.44.

First, we need to determine the shape of the composite body. Looking at the shaded area, we can see that it consists of two rectangles and a triangular section. We can combine these shapes to form a composite body that is rectangular at the bottom and triangular at the top.

Next, we need to find the coordinates of the centroid of the composite body. We can do this by finding the individual centroids of the rectangular and triangular sections and then using the weighted average method. The centroid of a rectangle is located at the center of the rectangle, so we can easily find the x and y coordinates of the centroid of the rectangular section. The centroid of a triangle is located at the intersection of its medians, which can be found using basic geometry. Once we have the coordinates of the centroids for each section, we can use the weighted average method to find the coordinates of the centroid of the composite body.

Once we have the coordinates of the centroid, we can use integration to find ix and iy. We can break up the composite body into small horizontal strips and use the formula for the moment of inertia of a rectangle and the moment of inertia of a triangle to find the contribution of each strip to the overall moment of inertia. We can then sum up these contributions using integration to find the total moment of inertia of the composite body about the x and y axes.

Overall, the process of finding ix and iy for a composite body using integration and the composite body approach can be a bit involved, but it is a useful tool for analyzing complex shapes. By breaking up a shape into simpler sections and using basic geometry and calculus, we can determine its properties and better understand how it will behave under different conditions.

To learn more about integration visit;

brainly.com/question/30900582

#SPJ11

Answer:

The hardenability increases with increasing austenite grain size, because the grain boundary area is decreasing. This means that the sites for the nucleation of ferrite and pearlite are being reduced in number, with the result that these transformations are slowed down, and the hardenability is therefore increased.

Answer:

I think it is false!

Explanation:

Answer: I think it's true

Explanation:

Because if you were part of a play, you would have a part but if you work on props, you don't have a part onstage.

Answer:

Diameter of pipe is 0.535 ft

Explanation:

see attachment, its works out 1st half

Although electric vehicle sales demand is on the rise, low availability of charging stations and short battery range are significant hurdles that Gaea must overcome. So correct option is A.

Electric vehicles (EVs) are vehicles powered by electric motors that use electricity stored in batteries instead of gasoline or diesel fuel. They have become increasingly popular in recent years due to the growing awareness of the negative impacts of internal combustion engines on the environment, such as air pollution and greenhouse gas emissions. EVs are also becoming more affordable and offer a much lower cost of ownership compared to traditional vehicles.

One of the key benefits of EVs is their low operating costs. Because they use electricity instead of gasoline, they have much lower fuel costs and require far less maintenance than traditional vehicles. Additionally, the lack of a traditional engine, transmission, and exhaust system means that EVs typically have fewer parts that can break down or require replacement, reducing the need for maintenance.

Another major advantage of EVs is their environmental benefits. By using electricity instead of gasoline or diesel fuel, EVs produce no emissions or very little emissions, depending on the source of the electricity used to charge them. This makes them a clean and efficient way to reduce greenhouse gas emissions and air pollution.

Finally, EVs offer a quiet and smooth driving experience, with instant torque and quiet operation. They are often equipped with advanced features, such as regenerative braking and electric power steering, that can further improve the driving experience. With a range of new models and options available, there is now an EV to meet the needs of virtually every driver.

To know more about charging stations visit:

https://brainly.com/question/11637757

#SPJ4

Answer:

yes it is very hard you should find a reccomended doctor to aid in your situation. But in the meantime how about you give me that lil brainliest thingy :p

The length is 2.4d

A torque is an angular force that tends to generate rotation along an axis, which could be a fixed point or the center of mass. Torque can also be conceived of as a spinning object's capacity to overcome turning resistance, such as a gear or a shaft.

Ancient Romans gave these necklaces the name "torque" by describing them as twisted and spiral screw-shaped using the Latin word "torquere," which also means "twisting" and "turning."

To ensure a good load distribution over the entire key length when the shaft becomes twisted when loaded in torsion, the key length should be less than approximately 1.5 times the shaft diameter.

To learn more about torque refer to:

https://brainly.com/question/17512177

#SPJ4

Answer:

A biological hazard

Explanation:

Biological because insects and other organisms thrive in stagnant water.

The type of hazard that is most likely to be exposed to a significant amount of stagnant water is known as biological.

A biological hazard may be defined as a biological substance that may significantly pose a great threat to the health of living organisms, primarily humans. These types are the major concerns in food processing because they cause most foodborne illness outbreaks.

In the case of Kris and James, they are significantly exposed to a biological hazard because stagnant water is commonly utilized by mosquitos to place eggs, this directs a lot of mosquitos around stagnant waters and therefore a higher risk of mosquito-transmitted diseases such as malaria. Besides this, stagnant water is highly polluted and includes bacteria and parasites that are harmful.

Therefore, the type of hazard that is most likely to be exposed to a significant amount of stagnant water is known as biological.

To learn more about Biological hazards, refer to the link:

https://brainly.com/question/14276262

#SPJ2

Answer:

The Material engineers trying to discover when they study different materials is described below in complete detail.

Explanation:

Material engineers analyze various elements to discover the purpose and explanation of its existence, the chemical characteristics, how long it has stood there, and how it influences human life. The material engineer is an engineering exercise that concentrates to enhance human activity by investigating the environment and the diverse elements or elements it holds.

Answer:

35.92 kpsi

Explanation:

Given data:

diameter of the steel bar d = 0.875 in

Area A = πd^2/4 = π(0.875)^2/4

length L = 15.0 ft

Load P = 21.6 kip

Modulus of elesticity E = 29×10^6 Psi

Assume we are asked to determine axial stress in the bar which is given as

\(\sigma = Load, P/ Area, A\)

\(\sigma = 4P/\pi d^2\)

substitute the value

\(\sigma = \frac{4\times 21.6}{\pi \times (0.875)^2} \\=35.92\ kpsi\)

I'd say number 4, number 3 looks like an exhaust valve

Answer:

Emails and phone calls are both common forms of communication that are used in professional and personal settings. There are several similarities between email and phone calls:

1. Both are asynchronous forms of communication: Unlike instant messaging or face-to-face conversations, both emails and phone calls allow the sender or recipient to respond at their convenience. They don't require immediate attention or an instant response.

2. Both are written forms of communication: While phone calls rely on spoken words, emails are written. As a result, both can be used to convey detailed information and allow the sender to carefully consider their words before sending.

3. Both are forms of direct communication: Emails and phone calls both allow for direct communication between two parties. This can be beneficial for discussing sensitive information or resolving issues quickly.

4. Both can be used for formal and informal communication: Emails and phone calls can be used in both personal and professional contexts. They are both flexible forms of communication that can be adapted to fit different situations.

5. Both require attention to tone and etiquette: Just like with phone calls, emails require attention to tone and proper etiquette. Both forms of communication should be approached professionally and respectfully to ensure effective communication.

In conclusion, while there are differences between emails and phone calls, there are also similarities that make them useful communication tools. Both allow for direct, asynchronous communication and can be adapted to fit different situations.

Explanation:

The correct answer is when retentive power is restored the accumulated count will be 300.

PLC counters are normally retentive; that is, whatever count was contained in the counter at the time of a proces- sor shutdown will be restored to the counter on power-up. The counter may be reset, however, if the reset condition is activated at the time of power restoration.A counter instruction is an input instruction. A counter's input signal can come from an external device such as a sensor. Up and down counters may be programmed together to count up and down. Counters can count past their preset values.

To learn more about retentive click the link below:

brainly.com/question/28851511

#SPJ4

Answer:

15psig

Explanation:

The correlation between acid rain and human population density in Russia is a complex issue that requires careful analysis and consideration of various factors.

Acid rain is caused by emissions of sulfur dioxide and nitrogen oxides, primarily from industrial activities and fossil fuel combustion. These pollutants can be transported over long distances by air currents and eventually deposited as acid rain.

When examining the correlation with human population density in Russia, several factors come into play. Areas with high population density tend to have more industrial and urban activities, which can contribute to higher emissions of pollutants. In densely populated regions with significant industrial activity, the likelihood of acid rain occurrence may increase.

Know more about acid rain here:

https://brainly.com/question/26775834

#SPJ11