Matter that stores energy in a readily useable form is termed ______. a. antimatter b. fuel c. phlogiston d. erg.
Answers
Matter that stores energy in a readily useable form is termed fuel. Option b is correct.
Fuel is a type of matter that stores energy in a form that can be easily used, such as gasoline or coal. matter refers to the physical substance, and energy is the capacity to do work. Fuel is a type of matter that can be converted into energy, which can then be used for various purposes.
Antimatter is a type of matter that has the opposite properties of regular matter, and is currently not used as a source of energy.
Phlogiston is a hypothetical substance that was once believed to be the cause of combustion, but has since been disproven.
Erg is a unit of measurement for energy.
Learn more about energy:https://brainly.com/question/13881533
#SPJ11
Matter that stores energy in a readily useable form is termed b. fuel.
the properties of automotive fuels and also discusses the factors governing the properties of fuels. The primary purpose of fuel is to supply energy; therefore, its calorific value is of prime importance. Both physical and chemical properties of gasoline differ greatly from those of diesel fuel. Motor gasoline is not a pure substance but a mixture of hydrocarbons with boiling points extending over a wide range. Consequently, its vapour pressure is a complex property that varies with both temperature and vapour/liquid ratio. There are three separate methods of measuring volatility that form the basis of commercial specifications: a prescribed form of distillation curve; a vapour pressure determination in specified conditions; and a “vapour-to-liquid ratio” determination. Gasoline contains gaseous hydrocarbons in solution such as butanes and the quantity of these gases is usually controlled by measuring the Reid vapour pressure.
learn more about fuel here:
https://brainly.com/question/12697105
#SPJ11
Related Questions
If a machine guard is missing or needs repair, you should ______________.
A) Ignore it
B) Immediately remove that machine from service
C) Continue using the machine
D) Tell someone when you get around to it
(This is for my Automotive class)
Answers
Step by step explanation
Answer:B
Explanation:
Javier’s class visited a power plant near his city, and they learned how it produced electricity. What does this form of power depend on for generating electricity?
Answers
The electricity is generated by the burning of fuel in the power plant that increases the kinetic energy of water vapor which rotates the turbine and shaft of the generator.
What is a power plant?A power plant is a place where heavy machinery objects are installed to produce electricity.
The power is generated in the power plant with the help of the burning of fuel that increases the temperature of the boiler. There are so many tubes in which water is present. Water absorbs heat and increases its kinetic energy. And this kinetic energy help to rotate the turbine and the shaft of the generator is attached to the turbine as result electricity is generated.
More about the power plant link is given below.
https://brainly.com/question/7670779
#SPJ4
instructions: as acting quality engineer, you have been asked to prepare a control plan for a customer that requires the following specifications: a. inside diameter 1.673 /- 0.001 inches b. outside diameter 3.562 /- 0.005 inches c. thickness 0.875 /- 0.0005 inches
Answers
Need help fast 50 points Project: Creating a Morphological Matrix
Assignment Directions
A systematic way to view common functionality of an object's structure and components is through a morphological matrix. You are going to utilize this method to analyze a common household device (from the list below or your own idea). First, create the left-hand column by deciding on the parameters that allow the object to function normally. For example, a pencil sharpener has a blade and a housing unit to support the system. Use the parameters to describe the system. If the pencil sharpener is hand operated, list the parameter of hand turning (either the pencil itself in a small unit or a handle in a wall-mounted device). The parameter column can include specific structures in the device, power sources, or any other information you learned in the lesson. The right-hand columns will include the current methods used by the device to complete the parameter, as well as any other options that would satisfy the parameter. You must create at least two other options for each parameter.
While the matrix provides valuable information for an engineer, it is typically more technological than a client or decision team needs. Therefore, you will also need to complete a one- or two-page analysis of the device, including the current parameter solutions and any recommended alterations to a design. Each recommendation must be supported by information in the morphological matrix.
Here are some ideas of household devices that you can analyze:
can opener
bathroom or kitchen scale
doorknob assembly
stapler
Assignment Guidelines
a completed morphological matrix
each parameter must have at least three solutions
a written analysis of the device with supporting details from the matrix
Submission Requirements
One to two pages double spaced
Proper grammar and vocabulary is required.
Answers
Answer:
The fundamental difference between effective and less effective matrix organizations is whether the tension between different perspectives is creative or destructive. While various processes, systems and tools can help, what matters most is what top leadership says and does and how that flows through the organization in shared targets, clear accountabilities, live team interactions and team-building transparency and behaviors.
Getting matrix management right is linked inextricably to an organization’s culture - the only sustainable competitive advantage. Key components of a culture can be grouped into behaviors, relationships, attitudes, values and the environment.
Environment and values: Each organization has its own environment, context and bedrock values. Everyone needs to know what matters and why. Don’t try to do anything else until you’ve got that set.
Attitude is about choices: An organization’s overall strategy drives choices about which of its parts will be best in class (superior), world class (parity), strong (above average), or simplified/outsourced to be good enough. These choices help determine the need for a matrix and how best to design it.
Relationships and behaviors: This is why organizations have matrices. The most effective of them best balance focus and collaboration. They allow leaders and teams to build differential strengths and then work together to make the best possible decisions and scale enterprises with a creative tension that they could not do on their own.
My colleague Joe Durrett has worked all sides of matrix organizations in marketing at Procter & Gamble, sales and general management at Kraft General Foods and CEO of Information Resources, Broderbund Software and Advo. He has seen matrices at their best and at their worst and offered his perspective for this article along with his partners John Lawler and Linda Hlavac. The 12 ways to make matrix organizations more effective were built on their ideas.
Explanation:
if they will be hot held foods previously prepared and refrigerated should be reheated to
Answers
If previously prepared and refrigerated foods are going to be hot held, they should be reheated before serving to ensure food safety. When it comes to hot holding prepared and refrigerated foods, reheating is essential to maintain food safety standards.
Reheating the food thoroughly helps kill any potential bacteria that might have grown during refrigeration and prevents foodborne illnesses. The reheating process should be done properly to ensure the food reaches a safe internal temperature, usually around 165°F (74°C), throughout. This temperature kills harmful bacteria and ensures that the food is safe to consume. It is important to follow proper reheating procedures, such as using appropriate heating equipment and ensuring even heating throughout the food, to avoid any hot or cold spots where bacteria can survive. By reheating previously prepared and refrigerated foods before hot holding, you can minimize the risk of foodborne illnesses and provide safe and enjoyable meals to your customers.
Learn more about food safety here: brainly.com/question/4226085
#SPJ11
an experiential learning method that uses structured activities to develop teamwork and leadership skills in trainees is known as _____.
Answers
The experiential learning method that uses structured activities to develop teamwork and leadership skills in trainees is known as team building. Team building is an effective way to improve communication, collaboration, and trust within a team. The activities involved in team building aim to challenge individuals and groups to work together towards a common goal, providing opportunities for trainees to develop leadership and problem-solving skills. These activities can take many forms, such as problem-solving challenges, outdoor adventure activities, or even games.
The goal of team building is to foster a positive and supportive team environment that allows individuals to learn from one another and to work towards a shared objective. Ultimately, team building can help organizations to achieve better performance, increased job satisfaction, and improved overall morale.
To learn more about problem click here: brainly.com/question/30142700
#SPJ11
You installed a new 40 gallon water heater with a 54,000 BTUh burner. The underground water temperature coming into the house is 55FHow long will it take to heat the water in the tank to a normal setting of 120F.Please show setup and calculations.
Answers
285. Longest Substring With K Typed Characters 1 2 3 4 5 6 USED public class Solution public String longest(String input, int k) { // Write your solution here } <> Description Notes Given a string, return the longest contiguous substring that contains exactly k type of characters. Return null if there does not exist such substring. Assumptions: • The given string is not null and guaranteed to have at least k different characters. .k > 0. Examples: • input = "aabcc", k = 3, output "aabcc". • input-"aabcccc", k-2, output = "bcccc" Console
Answers
To implement the `longest` method in the `Solution` class, you can use the sliding window technique to find the desired substring efficiently. Keep track of the count of each character in the window using a HashMap, and when the number of unique characters is greater than K, shrink the window by removing characters from the start. Keep updating the longest substring found during this process.
Based on your question, you're looking for a solution to the problem of finding the longest substring with exactly K typed characters in a given string. Here's a concise explanation using the terms you've provided:
1. Problem: Longest Substring With K Typed Characters
2. Method: public class Solution, public String longest(String input, int k)
3. Description: Given a string, find the longest contiguous substring that contains exactly K unique characters.
4. Assumptions: The given string is not null, has at least K different characters, and K > 0.
5. Examples:
- input = "aabcc", k = 3, output = "aabcc".
- input = "aabcccc", k = 2, output = "bcccc".
Learn more about window here:-
https://brainly.com/question/31252564
#SPJ11
Question 1) Which of the following materials is the best conductor of heat?
a) Low carbon steel
b) Cast iron
c) Lead
d) Copper
Answers
Explanation: Heat conductivity is a very important property when deciding which metal to use for a specific application. As copper is an excellent conductor of heat, it's good for heat exchangers, heat sinks, and even saucepan bottoms.
Hope this answer helps you...
Please mark me Brainliest...
What is the difference between a cost and a benefit?
Answers
Answer:
A cost is something you have to give up or sacrifice and a benefit is something that is gained or is helpful.
Explanation:
In a cost-benefit analysis of a system, an engineer is to simply look at the requirements for the system and determine the costs to build the system, both in financial value and energy value. Additionally, the engineer needs to determine the benefits that would come from choosing a particular path of cost. If the benefits outweigh the cost for the project, then the solution is accepted. Else, the cost outweighs the benefit and the solution is rejected.
The UHRS platform is optimized for Edge/Internet Explorer only. You can still use your favorite browser, but keep in mind that you may experience technical issues when working on UHRS with a different browser than Edge or Internet Explorer.
UHRS is optimized for...
Answers
It is to be noted that all UHRS platforms are optimized for the popular kinds of internet browser applications.
What is a UHRS?The Universal Human Relevance System (UHRS) is a crowdsourcing platform that allows for data labeling for a variety of AI application situations.
Vendor partners link people referred to as "judges" to offer data labeling at scale for us. All UHRS judges are bound by an NDA, ensuring that data is kept protected.
A browser is a software tool that allows you to see and interact with all of the knowledgeon the World Wide Web. Web sites, movies, and photos are all examples of this.
Learn more about internet browser applications.:
https://brainly.com/question/16829947
#SPJ1
Which of the following can cause a flopping sound at the front of the engine
A) drive belt too loose
B) timing chain too loose
C) drive belt too tight
D) timing chain too tight
Answers
please hurry i’ll give you 15 points
Answers
Answer:
measures, dissolves, liquid, carbon dioxide, evaporates, water vapor, mold, decompose
Consider the following data for 2008 in a small suburban community:
1. number of accidents: 360 fatal 10 injury 36 pdo 314
2. number of fatalities 15
3. area population: 50,000
4. registered vehicles 35,000
5. annual vmt: 12,000,000
6. average speed 30 mi/hr
compute all relevant exposure and population based accident and fatality rates for this data. compare these to national norms for the current year. (hint: use the internet to location current national norms)
Answers
Answer:
Motorcyclist Fatality and Injury Rates per Vehicle Miles Traveled, 1998-2008. 10. 9. Fatalities in School Transportation Related Crashes,. 1998-2008.
Explanation:
to modify the formatting of a carousel that’s created by the bxslider plugin, you can adjust
Answers
The bxslider plugin is a jQuery library that helps to create slideshows and carousels. With bxslider, it is easy to create dynamic sliders for your website.
bxslider provides several customization options that make it easy to modify the formatting of a carousel. In this case, we will discuss some ways to modify the formatting of a carousel that’s created by the bxslider plugin.To adjust the formatting of a carousel created by bxslider, we need to modify the CSS styles. This is because bxslider is based on HTML, CSS, and jQuery. We can use CSS to customize the look and feel of the bxslider carousel. For example, we can change the background color, font size, and image size.
We can also add borders, shadows, and other effects. The best way to customize the bxslider carousel is to use CSS selectors. This will allow us to target specific elements of the carousel and apply styles to them. For example, we can use the .bxslider selector to apply styles to the entire bxslider carousel. In conclusion, the bxslider plugin is a powerful tool for creating carousels and sliders. With its many customization options, it is easy to modify the formatting of a carousel.
Learn more about bxslider plugin: https://brainly.com/question/29313631
#SPJ11
A child under the age of 8 years __________, when all the rear seats are already occupied by children under the age of 7 years.
Answers
A child under the age of 8 years may sit in the front seat when all the rear seats are already occupied by children under the age of 7 years.
The occupancy rate by children under the age of 7?
The occupancy of buildings by children under the age of 7 is an important consideration in building design and safety. In many countries, building codes and regulations specify requirements for the design and construction of buildings that will be occupied by young children.
For example, in the United States, the International Building Code (IBC) and International Residential Code (IRC) provide guidelines for the design and construction of buildings that will be occupied by children under the age of 7. These codes specify requirements for things such as guardrails, handrails, stairs, and window openings to prevent falls and injuries.
Other considerations for buildings occupied by young children may include the use of non-toxic materials and finishes, childproofing measures such as cabinet locks and electrical outlet covers, and appropriate ventilation and heating systems.
It's important for architects, builders, and building owners to carefully consider the needs and safety of young children when designing and constructing buildings that will be occupied by them. By following appropriate guidelines and regulations, they can help ensure the safety and well-being of young occupants.
to know more about children under age of 7
https://brainly.com/question/13049269
#SPJ11
Water is traveling through a horizontal pipe with a speed of 2.5 m/s and at a pressure of 160 kPa. This pipe is reduced to a new pipe which has a diameter half that of the first section of pipe. Determine the speed and pressure of the water in the new, reduced in size pipe.
Answers
The speed of water in the reduced-size pipe is 10 m/s, and the pressure depends on the density of water.
To determine the speed and pressure of water in the new, reduced-size pipe, we can apply the principle of continuity and Bernoulli's equation.
According to the principle of continuity, the mass flow rate of water remains constant in a closed system. Therefore, the product of the water's velocity and the cross-sectional area of the pipe remains constant.
Let's denote the initial diameter of the first section of pipe as D1 and the diameter of the reduced pipe as D2 (which is half of D1).
Since the cross-sectional area is directly proportional to the square of the diameter, we have:
A1/A2 = (D1^2)/(D2^2) = 1/4
Now, let's apply Bernoulli's equation between the two sections of the pipe:
P1 + (1/2)ρV1^2 = P2 + (1/2)ρV2^2
where P1 and P2 are the pressures at the respective sections, ρ is the density of water, V1 is the initial velocity, and V2 is the velocity in the reduced pipe.
Since the pipe is horizontal, we can neglect the height term in Bernoulli's equation.
Given:
V1 = 2.5 m/s
P1 = 160 kPa (which can be converted to Pa: 160,000 Pa)
D2 = (1/2)D1
First, let's solve for V2 using the principle of continuity:
A1V1 = A2V2
(D1^2)(2.5) = (D2^2)V2
(D1^2)(2.5) = [(1/4)D1^2]V2
V2 = 10 m/s
Now, substitute the known values into Bernoulli's equation to solve for P2:
P1 + (1/2)ρV1^2 = P2 + (1/2)ρV2^2
160,000 + (1/2)(ρ)(2.5^2) = P2 + (1/2)(ρ)(10^2)
160,000 + (1/2)(ρ)(6.25) = P2 + (1/2)(ρ)(100)
160,000 + 3.125ρ = P2 + 50ρ
160,000 = P2 + 46.875ρ
P2 = 160,000 - 46.875ρ
The pressure in the reduced-size pipe, P2, depends on the density of water. To determine the exact value of P2, we would need to know the density of water.
In summary, the speed of water in the reduced-size pipe is 10 m/s, and the pressure depends on the density of water.
Learn more about Bernoulli's equation here:
https://brainly.com/question/33293474
#SPJ11
Consider the signal x(t) = e-5tu(t -1), and denote its Laplace transform by X(s). (a) Using eq. (9.3), evaluate X(s) and specify its region of convergence. (b) Determine the values of the finite numbers A and to such that the Laplace transform G(s) of g(t) = Ae-51 u(-t-to) has the same algebraic form as X(s). What is the region of convergence corresponding to G(s)?
Answers
The region of convergence corresponding to G(s) will be To = -1 and A = 1
How to illustrate the information?Based on the information given, it should be noted that the value when we evaluate X(s) and specify its region of convergence will be:
X(s( = e^(5 + 5)/(5+5)
= -5.
The region where the function exists in the transfer function's pole/zero plot is known as the Region of Convergence. We prefer to deal with rational functions for the purpose of practical filter design, which may be defined by two polynomials, one for identifying the poles and the other for calculating the zeros, respectively.
The values of the finite numbers A and to such that the Laplace transform G(s) of g(t) = Ae-51 u(-t-to) has the same algebraic form as X(s) will be - 1 and the region of convergence corresponding to G(s) is 1.
Therefore based on the information, the region of convergence corresponding to G(s) will be To = -1 and A = 1.
Learn more about convergence on:
brainly.com/question/1521191
#SPJ1
5. According to the FMCSRs, you are qualified to operate a CMV if you:
A. are at least 15-years old.
B. have passed an IQ test.
C. have only one current CDL.
D. are currently disqualified from operating a motor vehicle.
Answers
Answer:
currently states that a person is qualified to drive a commercial motor vehicle if he/she “can read and speak the English language sufficiently to converse with the general public, to understand highway traffic signs and signals
So I think B
The term route of entry on an sds refers to the way a ___ enters the body
Answers
The correct answer is A) Chemical
Explanation:
The abbreviations SDS means Safety Data Sheet, which refers to a very complete document about chemicals and safety related to these, including their properties and potential hazards, as well as, procedures or steps to avoid hazards and accidents.
This means the main focus of this document is chemicals; moreover, in this, there is information about the route of entry, which refers to the way chemical can enter the body and includes through inhalation, ingestion, contact with skin, among others. Also, depending on the chemical some routes of entry represent a major hazard. According to this, the correct answer is A.
Answer: Chemical!!!
Explanation:
In the circuit given below, R1 = 17 kΩ, R2 = 74 kΩ, and R3 = 5 MΩ. Calculate the gain 1formula58.mml when the switch is in position 1, position 2, and position 3.
A) The gain 1formula58.mml at the position 1 is _____.
B) The gain 1formula58.mml at the position 2 is _____.
C) The gain 1formula58.mml at the position 3 is _____.
Answers
Answer:a
a) Vo/Vi = - 3.4
b) Vo/Vi = - 14.8
c) Vo/Vi = - 1000
Explanation:
a)
R1 = 17kΩ
for ideal op-amp
Va≈Vb=0 so Va=0
(Va - Vi)/5kΩ + (Va -Vo)/17kΩ = 0
sin we know Va≈Vb=0
so
-Vi/5kΩ + -Vo/17kΩ = 0
Vo/Vi = - 17k/5k
Vo/Vi = -3.4
║Vo/Vi ║ = 3.4 ( negative sign phase inversion)
b)
R2 = 74kΩ
for ideal op-amp
Va≈Vb=0 so Va=0
so
(Va-Vi)/5kΩ + (Va-Vo)74kΩ = 0
-Vi/5kΩ + -Vo/74kΩ = 0
Vo/Vi = - 74kΩ/5kΩ
Vo/Vi = - 14.8
║Vo/Vi ║ = 14.8 ( negative sign phase inversion)
c)
Also for ideal op-amp
Va≈Vb=0 so Va=0
Now for position 3 we apply nodal analysis we got at position 1
(Va - Vi)/5kΩ + (Va - Vo)/5000kΩ = 0 ( 5MΩ = 5000kΩ )
so
-Vi/5kΩ + -Vo/5000kΩ = 0
Vo/Vi = - 5000kΩ/5kΩ
Vo/Vi = - 1000
║Vo/Vi ║ = 1000 ( negative sign phase inversion)
If an EDM instrument has a purported accuracy capability of ±(1.5 mm + 2ppm) what error can be expected in a 25 ft measured distances (assume that the instrument and target mis-centering errors are equal to zero).
Answers
If an EDM instrument has a purported accuracy capability of ±(1.5 mm + 2ppm) error can ±1.50 mm.
What is EDM instrument?A surveying tool used to measure distance electronically between two sites using electromagnetic waves is an electronic distance measurement device.
EDM instruments are extremely dependable and practical surveying tools that can measure distances up to 100 kilometres.
Here, it is given that:
Accuracy capacity = ±(1.5 mm + 2ppm)
Measured distance = 25 m
\(E_i = E_r=0\)
\(E_d=\sqrt{0^2+0^2+(1.5)^2+2PpmX[\frac{10^-^6}{Ppm}X25X\frac{10^3mm}{m} ]^2 }\)
\(E_d=\sqrt{2.25+(2X10^-^6X25X10^3)^2}\)
\(E_d= 1.50 mm.\)
Thus, the answer is ±1.50 mm.
For more details regarding EDM instrument, visit:
https://brainly.com/question/15452991
#SPJ1
Tidal turbines convert the energy of a flowing tide to generate electricity. Early designs of these machines commonly had their rotor attached to a supporting tower mounted on the seabed – see for example Figure QC2.1. A representation of a tide-driven flow of water past a tidal turbine is sketched in Figure QC2.2. An expansion of the flow from d1 to d2 is imagined to occur over the rotor, with half of the expansion (in area) happening upstream of the rotor, and half downstream.
(a) Explain why the active part of the inflow (the streamtube shown in Figure
QC2.2) expands its cross-section as it passes the turbine. (2)
Analysis for the analogous situation of a wind turbine with uniform inflow, attributed to Albert Betz and others in the 1920s, demonstrated that for optimum efficiency of energy extraction from the inflow, the far upstream flow speed should be reduced by the turbine such that the far downstream speed is 1/3rd of the far upstream speed.
(b) Suggest three reasons why this theoretical maximum efficiency will in general
not be achieved in a practical tidal turbine deployment. (3)
(c) The Alstom 1.4 MW OceadeTM turbine has a rotor diameter of 18 m. The
supporting tower has a height of 15 m and a diameter of 3 m. In a 3 ms-1 tidal
flow, estimate the total fluid loading experienced by the whole machine. State
and justify the assumptions that you make in arriving at this estimate. (12)
(d) How would you expect to use these estimates of forces when designing the
turbine and tower structure?
Answers
(a) The active part of the inflow expands its cross-section as it passes the tidal turbine due to conservation of mass and energy.
(b) Several reasons contribute to the theoretical maximum efficiency not being achieved in practical tidal turbine deployments, including turbulence, non-uniform flow, and mechanical losses.
(c) Estimating the total fluid loading on the Alstom 1.4 MW OceadeTM turbine requires considering the flow velocity, rotor and tower dimensions, and making assumptions about the flow characteristics and structural properties.
(d) The estimates of forces obtained from the fluid loading calculations are essential for designing the turbine and tower structure by ensuring that they can withstand the anticipated loads and stresses.
(a) The active part of the inflow expands its cross-section as it passes the tidal turbine due to the principle of conservation of mass and energy. As the tidal flow encounters the turbine rotor, some of the kinetic energy of the flow is converted into mechanical energy to drive the turbine. To satisfy the conservation of mass, the cross-sectional area of the flow must increase to compensate for the reduction in flow velocity caused by energy extraction.
(b) Achieving the theoretical maximum efficiency in practical tidal turbine deployments is challenging due to several reasons. First, tidal flows are often characterized by turbulence, which disrupts the uniformity of the flow and reduces overall efficiency. Second, tidal flow itself is not uniformly distributed, and the flow characteristics vary with tidal cycles, further impacting efficiency. Lastly, mechanical losses in the turbine's components, such as friction and resistance, reduce the efficiency of energy conversion.
(c) Estimating the total fluid loading on the Alstom 1.4 MW OceadeTM turbine involves considering the flow velocity, rotor diameter, and tower dimensions. Assuming a tidal flow velocity of 3 m/s, the fluid loading can be estimated by considering the momentum change and forces acting on the rotor and tower surfaces. Assumptions may include a simplified flow model, neglecting factors such as turbulence and non-uniform flow, and assuming a stationary tower. These assumptions simplify the calculation while providing a reasonable estimate of the fluid loading.
(d) The estimates of forces obtained from the fluid loading calculations are crucial for designing the turbine and tower structure. These estimates help engineers determine the required structural strength, material selection, and design considerations to ensure that the turbine and tower can withstand the anticipated fluid forces and mechanical stresses. By considering the estimated forces, designers can optimize the structural integrity, stability, and reliability of the turbine and tower, ensuring safe and efficient operation in tidal environments.
Learn more about flow velocity here:
https://brainly.com/question/14441268
#SPJ11
A resistor has code 104 printed on it .What is the resistive value of this resistor
Answers
Answer:
X = 1 (1st digit in the code)
Y = 0 (2nd digit)
Z = 4 (3rd multiplier digit)
104 → 10 × 10^4 Ω
→ 10 × 10000Ω
→ 100 kΩ
resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).
Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.
When we use numbers, let's assume that we have 3 single-digit numbers abc.
So if the code in our resistor is abc, this will mean that the resistance of the resistor is:
ab×10^c Ω
Using this general rule we can see that if the code is 104, then the resistance will be:
r = 10×10^4 Ω
= 100,000 Ω
Then we can conclude that the resistive value of this resistor is 100,000 Ω
If you want to learn more, you can read:
https://brainly.com/question/74415
According to blank law a liquid in a confined space is not compressed.
A. Newton's fourth
B. Charles's
C. Pascal's
D. Boyle's
Answers
Answer:
C. Pascal's
Explanation:
Pascal's law states that a liquid in a confined space has equal pressure distribution among the inside of the confined space. Due to this pressure, we know that these fluids cannot be compressed in a confined space any more than they already are.
Ethylene glycol, the ingredient in antifreeze, does not cause health problems because it is a clear liquid
Answers
Answer:
False
Explanation:
I got it wrong picking true
.Find Ib. Express your answer to three significant figures in either rectangular OR degree-polar form. (Use the r∠θ template or rcis(θ) for degree-polar entries.)
Find Z. Express your answer to three significant figures in either rectangular OR degree-polar form. (Use the r∠θ template or rcis(θ) for degree-polar entries.)
Answers
Without specific information or equations, the values of Ib and Z cannot be determined.
What is the value of Ib and Z in the given context?The given question asks to find the value of Ib and Z. However, without specific information or equations provided, it is not possible to determine the values or the context in which they are being calculated.
To find Ib, we would need additional information such as the equation or circuit involved. Similarly, to find Z, we would need information about the specific problem or system in which Z is relevant.
Without such details, it is not possible to provide an explanation or solve the problem.
Learn more about Ib
brainly.com/question/12145534
#SPJ11
pls provide as much detail as possible
Answers
We do not have enough evidence to conclude that A has a smaller hardness value than B at the 0.05 level of significance.
How to explain the informationWe observe that the critical value for a one-tailed test at the 0.05 level of significance is -1.796. Since our surveyed t-value surpasses the critical value, we are unable to dismiss the null hypothesis. We lack necessary data to conclude that A has a less hard value than B at the 0.05 level of significance.
Considering further, we identify the critical value for a two-tailed test at the 0.05 level of significance to be ±2.120. As our calculated t-value falls beneath this cut off, we refuse to reject the null hypothesis; lacking evidence to establish a difference between the population means of the number of hydraulic pumps for Type A and Type B machines at the 0.05 level of certainty.
Learn more about hypothesis on
https://brainly.com/question/606806
#SPJ1
5 Systems Modeling
es / SPE(2201 / General / Business System Modelling CAT
2. Business Process Modelling is important to a business due to the following advantages except:
(2 marks)
O a. None of the above
h
O b. Enhances Customization of Business Processes
O c Enhances Competitive advantage
O d. Enhances Process Communication
age
Next pag
Answers
Answer: None of the above
Explanation:
Business process modeling refers to the graphical representation of the business processes of a company, which is vital in the identification of potential improvements.
Business pticess modelling can be done through graphing methods, like data-flow diagram, flowchart etc. It is vital as business managers can effectively and quickly communicate their ideas.
It also enhances the customization of business processes, enhances the competitive advantage and enhances the process communication as well.
Therefore, the answer to the question will be "None of the above".
you wish to set california (abbreviated ca) as a default value. what do you type into the expression builder?
Answers
To set "California" as the default value using the expression builder, you would type the following: "ca" or "California".
The exact syntax may vary depending on the specific system or programming language you are using, but in general, you would need to assign the desired default value to the corresponding variable or field. In this case, you would use the abbreviation "ca" or the full name "California" as the value to be set as the default.
It's important to consult the documentation or guidelines of the specific system or programming language you are working with to ensure the correct syntax and usage for setting default values using the expression builder.
Learn more about California here: brainly.com/question/32361197
#SPJ11